This softener is timer controlled which means that the user must set the frequency of regeneration* eg once a week at 2:00 am.

This water softener is available in four sizes:

4 litre: This softener measures 530 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 160 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 667 litres.

10 litre: This softener measures 635 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 400 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 1667 litres.

15 litre: This softener measures 695 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 600 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 2333 litres.

22 litre: This softener measures 815 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 880 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 3667 litres.

* Regeneration refers to the process a water softener goes through to "regenerate" or clean its resin ready to be re-used. This is done automatically by the softener by passing a salt solution through the resin typically once a week and is usually done during a period where the softener is unlikely to be used i.e. 2:00 am.

**The capacity of the resin is the amount of water that can be treated before the resin becomes exhausted and must be "regenerated". The figures given above assume a calcium carbonaet level of 300 parts per million (ppm). If your CaCO3 level is lower the capacity of your resin will be greater, if it is higher then the capacity will be lower. The easiest way to get your hardness level is to call your water supplier and ask them for the average figure for your area.

This softener is METER controlled which means that the softener will measure teh treated water and regenerate when it needs to.

This water softener is available in three sizes:


10 litre: This softener measures 635 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 400 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 1667 litres.

15 litre: This softener measures 695 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 600 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 2333 litres.

22 litre: This softener measures 815 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 880 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 3667 litres.

This softener is timer controlled which means that the user must set the frequency of regeneration* eg once a week at 2:00 am.

This water softener is available in four sizes:

4 litre: This softener measures 530 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 160 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 667 litres.

10 litre: This softener measures 635 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 400 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 1667 litres.

15 litre: This softener measures 695 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 600 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 2333 litres.

22 litre: This softener measures 815 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 880 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 3667 litres.

* Regeneration refers to the process a water softener goes through to "regenerate" or clean its resin ready to be re-used. This is done automatically by the softener by passing a salt solution through the resin typically once a week and is usually done during a period where the softener is unlikely to be used i.e. 2:00 am.

**The capacity of the resin is the amount of water that can be treated before the resin becomes exhausted and must be "regenerated". The figures given above assume a calcium carbonaet level of 300 parts per million (ppm). If your CaCO3 level is lower the capacity of your resin will be greater, if it is higher then the capacity will be lower. The easiest way to get your hardness level is to call your water supplier and ask them for the average figure for your area.

This softener is METER controlled which means that the softener will measure teh treated water and regenerate when it needs to.

This water softener is available in three sizes:


10 litre: This softener measures 635 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 400 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 1667 litres.

15 litre: This softener measures 695 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 600 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 2333 litres.

22 litre: This softener measures 815 mm high x 275 mm wide by 440 mm deep.
The service flow rate is 880 l/hr although it is capable of higher flow rates.
Its **capacity at 300 ppm calcium carbonate is 3667 litres.

This hood fits over the top of the softener head to give it a more aesthetically pleasing appearance.